Bandit Alley

MODEL SPECIFIC => BIG BANDIT BANTER => Topic started by: apw100 on May 16, 2005, 09:13:21 PM

Title: Polishing a Bandit 1200 frame- Any opinions?
Post by: apw100 on May 16, 2005, 09:13:21 PM
I am purchasing a Bandit 1200 for a streetfighter project and am considering polishing the frame. Anyone have, or seen, any polished Bandit frames? Opinions?  
Obviously, I will have to take the bike apart and remove the engine to polish the frame.  What equipment will I need? Thanks
Title: Frame Polishing?
Post by: gshok108 on May 16, 2005, 10:02:13 PM
I am assuming you know the Bandit is a steel framed bike?  You can polish the aluminum swing arm, triples, wheels, etc, but the frame....You are either stuck with paint, or chroming.  

If you want to polish the aluminum bits, a quick google search will turn up many how to sites.
Title: Polishing a Bandit 1200 frame- Any opinions?
Post by: PeteSC on May 16, 2005, 10:14:09 PM
Dittos on the steel frame.   But you can polish out the wheels, and swingarm, if you feel like polishing something.
   There's plenty of other parts that can be 'blinged' out....
Title: frame
Post by: tacoman on May 17, 2005, 01:24:28 PM
I don't know the cost but I've seen some custom dirt bikes with steel frames and the builders usually go with nickel plating.  It looks great.  If not that probably some powder coating would have a nice result.
Title: Polishing a Bandit 1200 frame- Any opinions?
Post by: land_shark on May 17, 2005, 01:49:09 PM
Bummer.   :boohoo:   I was considering polishing as well.  Can you sand it down and clear coat it for the same effect?  Also, can anyone gauge how labor intensive it is  to yank out the frame?  I realize this all depends on mechanical experience (of which I have some; replaced fork springs, some carb work, about to do valves this weekend).



Thanks!
Title: Polishing a Bandit 1200 frame- Any opinions?
Post by: Red01 on May 18, 2005, 05:05:37 AM
The kind of steel they use for frames wouldn't ever polish up to a nice shine.

If you're thinking about tearing the bike apart to have the frame plated (nickel, chrome, gold, etc.), an average shadetree mech with the tools should be able to tear it down in a day. Puting it all back together, probably 2-3X that. Take LOTS of pictures & notes. The frame would be out to a plater's for several days (at best) and you stand a high liklihood of fogetting where some of the details go back.

Nothing too technical about the job, but you will need torque values for reassembly
Title: Polishing a Bandit 1200 frame- Any opinions?
Post by: Chi-TownBandit on May 19, 2005, 12:22:16 PM
I took apart my B6, when I had it, for an engine swap.  This past weekend I just helped a buddy take apart his FZR to help rebuild his engine, so I know a little bit about this process.  
I think a service manual (which should have all the torque settings), a torque wrench, and a bucket of loctite are the basics for this job.  Also, having a buddy for a second pair of eyes is always a good thing, especially when you're putting the bike back together again--which is the most time consuming part of the whole the process because of lining the engine back up to the frame, torquing bolts down to specs, and then putting the wiring harness back on.  Just be careful not to overtighten things so as not to mess up the engine block.
Title: Polishing a Bandit 1200 frame- Any opinions?
Post by: smooth operator on May 22, 2005, 08:14:32 AM
I think powder coating the frame is the way to go. I polished the swing arm, and I'll wait till I feel the need to do some head work befor tearing everything apart. Sounds like a winter project.