« previous next »
Pages: [1]

Author Topic: Starting In Gear  (Read 4485 times)

Offline Warren

  • New user!
  • *
  • Posts: 6
Starting In Gear
« on: September 24, 2006, 12:49:09 PM »
I have a 2000,  B600S and I sometimes have trouble starting when I have the bike in gear.  It starts fine in nuetral without the clutch.  When I put her in gear and pull in the clutch to start, I get nothing.  It does not happen all of the time.  Also when it does start in gear, I feel a load on the motor (it tries to pull forward like I am letting the clutch out).

Can anyone tell me if there is some kind of switch that is malfunctioning or is my clutch lever not adjusted correctly.

Thanks for the advice all.
Logged

Offline KX5000

  • Board Homesteader!
  • ***
  • Posts: 155
Starting In Gear
« Reply #1 on: September 24, 2006, 02:03:09 PM »
sounds like your clutch might be out of adjustment
Logged
3 Kids
2 Dogs
1 Wife
NO problem!(yeah right!!)

Offline Rocketjock

  • Board Homesteader!
  • ***
  • Posts: 293
Starting In Gear
« Reply #2 on: September 24, 2006, 02:03:33 PM »
You shouldn't feel any clutch drag. Sounds like an adjustmant is required. As for the no start, mine is equipped with a safety kill switch on the side stand. I occasionally go to start off with the stand down and it immediately kills the engine. A somewhat annoying but practical switch. If that switch is occasionally shorting, you may have the occasional no start. Hope this helps.
Logged
06 B12
Lovin my Bandit
07 KLR.
Too much fun!

Offline chupacabra

  • Board Homesteader!
  • ***
  • Posts: 329
Starting In Gear
« Reply #3 on: September 24, 2006, 02:37:15 PM »
When the bike is cold the oil will cause the clutch to drag a little.
Logged
Dave . . . San Diego, California
1996 GSF600S Marble Italian Red
I bought new in sept of 95
D.I.D. 530ZVM gold x-ring chain
Pirelli Diablo 120/60F & Strada 160/60R
Progressive fork springs
H.S. HD rear axle nut & washer
Hole Shot 17" comp1 can

Offline Airmotive

  • Board Homesteader!
  • ***
  • Posts: 86
Starting In Gear
« Reply #4 on: September 24, 2006, 10:05:55 PM »
When the bike does not start, is it at least kicking over or is it completely unresponsive to the starter switch?

If it's unresponsive, a grounded kick stand switch would be on my top-of-the-pops.
Logged
Give a man a match, and he'll be warm for a minute, but set him on fire, and he'll be warm for the rest of his life.

Offline Red01

  • Board Homesteader!
  • ***
  • Posts: 8977
  • Are we having fun yet?
Starting In Gear
« Reply #5 on: September 25, 2006, 06:23:46 AM »
In addition to the sidestand switch mentioned above, you may be suffering an intermittent problem with the switch on the clutch lever.

If the engine pulls with the clutch in and the oil is warm, it's time to adjust the clutch... but the engine should still start (cold or warm), as the starter circuit doesn't monitor the clutch adjustment, just when the lever is pulled in.
Logged
Paul
2001 GSF1200S
(04/2001-03/2012)
2010 Concours 14ABS
(07/2010-current)

Offline clutch7

  • New user!
  • *
  • Posts: 6
Starting In Gear
« Reply #6 on: October 04, 2006, 04:48:11 PM »
I have a 2K B6 as well. When I start in gear I sometimes get a bit of a pull even if the clutch is in. But it usually starts fine.
Logged
Pages: [1]
« previous next »