Author Topic: Holeshot Stage 1 (Read 5334 times)

SHREDDER · « **on:** December 18, 2006, 01:12:56 AM »

I just helped a friend install a Holeshot Stage 1 Jet Kit on an 03 B6 but can't get it to run right. Any tricks or tips to tweak it just right?

SHREDDER · « **Reply #1 on:** December 18, 2006, 01:32:25 AM »

Also I installed the #95 main jets with 2 shims per needle.

solman · « **Reply #2 on:** December 18, 2006, 11:03:03 PM »

Quote

but can't get it to run right.

Could you be a bit more specific?

SHREDDER · « **Reply #3 on:** December 19, 2006, 01:54:36 PM »

The idle is all over the place and when you hit the gas the engine shuts off.

PaulVS · « **Reply #4 on:** December 19, 2006, 02:02:17 PM »

Stuck float?

PaulVS · « **Reply #5 on:** December 19, 2006, 02:13:06 PM »

Double post

SHREDDER · « **Reply #6 on:** December 20, 2006, 05:40:00 AM »

The floats looked alright when I had the carbs apart.

Thief400 · « **Reply #7 on:** December 20, 2006, 10:26:44 AM »

vacuum leak

ZenMan · « **Reply #8 on:** December 20, 2006, 10:33:16 AM »

Sorry if this is out of place, but I just got off the phone with Dale Walker of Holeshot Performance and found him to be rude and interruptive. I had called to ask him what he knew about the new 1250, and I couldn't get a word in edgewise to ask any questions! When I finally got to tell him that I had one on order for January, he told me my dealer is "full of crap". He also was very sarcastic and arrogant when I told him that I was willng to make my own elbow pipe to fit one of his slip-ons, telling me, "yeah, good luck with that, buddy".

I have no idea if his products are any good, but I won't be ordering anything from Holeshot now.

Sorry for the rant, I'm just not used to being talked to that way at my age (50's).

I hope you get your problems worked out, Shredder.

SHREDDER · « **Reply #9 on:** December 20, 2006, 04:48:49 PM »

My friend actually got the same kind of response from him. I'm now suspecting it might be a vacuum problem. I'm not certain I reconnected the hoses properly when I put the bike back together. The damn Clymer manual shows pictures of the hoses but does not show where they go. I don't understand how they can have a wiring diagram but not a hose diagram.

SHREDDER · « **Reply #10 on:** December 23, 2006, 03:31:16 PM »

It turned out that I misconnected some vacuum hoses. It works just fine now!

solman · « **Reply #11 on:** December 24, 2006, 02:47:28 AM »

Glad to hear that you sorted out the problem. It is amazing that most of the time, the problem is something simple.

rider123 · « **Reply #12 on:** January 05, 2007, 03:04:55 PM »

The new 2007 1250 is fuel injection not carbuerators, hence there is no jet kit for it. You would have to use a programmable engine management system like a power commander to reprogram the fuel injection mapping. I'm sure the guys at power commander will offer one for the 2007 Bandit 1250 eventually. Glad you have it working.

Bob Holland · « **Reply #13 on:** January 05, 2007, 04:08:00 PM »

Quote from: "ZenMan"

Sorry if this is out of place, but I just got off the phone with Dale Walker of Holeshot Performance and found him to be rude and interruptive. I had called to ask him what he knew about the new 1250, and I couldn't get a word in edgewise to ask any questions! When I finally got to tell him that I had one on order for January, he told me my dealer is "full of crap". He also was very sarcastic and arrogant when I told him that I was willng to make my own elbow pipe to fit one of his slip-ons, telling me, "yeah, good luck with that, buddy".

I have no idea if his products are any good, but I won't be ordering anything from Holeshot now.

Sorry for the rant, I'm just not used to being talked to that way at my age (50's).

I hope you get your problems worked out, Shredder.

I have delt with Dale Walker a few times, and have always got a great response from him, He must have had a New Years hangover