22 Mar 2018 - As David Bowie said: bike “Ch-ch-changes”Well, the KTM 200 is going. Last summer we had an “incident” that cemented the decision to move to a smaller dirt bike again. After seeing a young guy ruin thousands of $ in braces / dental work hitting the cross bar on his bike, I rode for about 20 mins before a jump bested me (arms “buckled” and ...
Hi all, I apologize if this particular question has been previously asked & answered, but I've tried searching (both here and elsewhere on the web) and have not found all the information I'm looking for.
I'm replacing the stock shock on my '93 B4; from what I've read one of the readily a... 12 Feb 2018 - 92 gsf250p jet needle kit :duh:hi .last days i got carburator jet kit.main jet 105#,pilot jet 12.5#,starter jet 40# and new jet. needle and needle jet.now how to adjust needle clip position and pilot air screw.
30 Jan 2018 - 2002 Bandit 1200 speedometer not working
Written by bluebandit02
posted in SUZUKI BANDIT 600 thru 1200 - AIR/OIL COOLED TECHNICAL
January 30, 2018, 04:18:06 PM
547 Views
Good day folks,
I know this has been discussed on here but it was years ago and it was suggested I start a new discussion. My back is the 2002 1200S So the other day on my way to work my speedo started to go. I was going over 50km for sure but it wouldnt go any higher than 40km/h.... 08 Jan 2018 - OEM chain or aftermarket
Written by plhcpat
posted in SUZUKI BANDIT 650 and 1250 - WATER COOLED TECHNICAL
January 08, 2018, 08:11:21 PM
383 Views
4th time trying to post 2007 1250 18765ish on miles. What is everyone doing
28 Dec 2017 - Newbie needs gsf250 "big bore" adviceHi All and sorry to bother you with this but I've been trying to work out my big bore options from the FAQs and previous postings and I'm getting a bit lost. I have a year 2000 gsf250 - what if any are my big bore options? Is there any way to take it out to a 400 with the internals from that engine?...
28 Dec 2017 - CHAIN wear & sprocket alignment
Written by China Greg
posted in SUZUKI BANDIT 600 thru 1200 - AIR/OIL COOLED TECHNICAL
December 28, 2017, 06:59:47 PM
610 Views
First Gen 1200's
...seem to have a DESIGN flaw. I was having chain wear issues...only getting 5-8000 miles on a chain. There was also a lot of sprocket-chain CLATTERING noise, especially at the rear sprocket. I tried a few things... finally discovered: 1) the ... 15 Nov 2017 - Rough CHAIN issues
Written by China Greg
posted in SUZUKI BANDIT 600 thru 1200 - AIR/OIL COOLED TECHNICAL
November 15, 2017, 05:59:27 PM
527 Views
For the longest time, (50K miles??) I've been having issues with my chain and sprockets.
Primarily, there has been a..louder-than-I-expect.. CLATTER across the sprockets. Also, I was going through chains faster than normal (averaging 7-8K only). I did a LOT of homework... ... 14 Nov 2017 - o ring number 11143-32f00
Written by EvilRanger
posted in SUZUKI BANDIT 600 thru 1200 - AIR/OIL COOLED TECHNICAL
November 14, 2017, 05:10:28 PM
579 Views
Hello all, I am reinstalling my head and am in need of some info. I am replacing the 6 head o rings part # 11143-32F00. I have looked all over and cannot find specifications for this part. Does anyone have these specs? Thanks. Basically I am cheap and would like to source them elsewhere than Suzuki.
07 Oct 2017 - Bandit 400 Motor BuildMotor rebuild after a blown head gasket.
.5 mm piston and rings gsxr 400 cams Factory Pro shift kit Barnet clutch re -look at a GSXR 1100 swing arm conversion from my current RF 900 conversion. https://www.pinterest.com/tjasonstanl8049/bandit-400-motor-build/ 03 Sep 2017 - GS500 Tail Light swap ?I did a tail tidy last year and had to install an aftermarket light for the lisence plate. It works well, but it's a blue-ish light and it kind of clashes with the age of the bike.
I thought about this and I started looking for compatible headlights. My buddy had a gs500 from the same era... 13 Jun 2017 - Foot Peg optionFound the following, ...since you can't order the Yosh one any more!
https://www.nicecycle.com/Suzuki-Foot-Peg-p/s-peg-bandit.htm
|
Ad
|
Welcome, Guest. Please 
April 22, 2018, 10:41:51 PM